August 20, 2022


Programming Language/Web Design and Development

How To Build A Pc From Scratch how to build a computer

The suggested sequence of which memory slots to be installed first may differ due to different motherboards. Take MSI motherboards as example, you are suggested to insert the memory kit into Dimm1 slot first. Don’t forget to always check the dimensions of the graphics card before purchasing so you can evaluate and see whether or not it’ll fit just right inside the case.

As such, make sure you do your research prior to making any selection. From there you’ll want to thermal paste if your CPU cooler didn’t come with any pre-applied already. Users will want to squeeze out a small blob, around the size of half a pea, onto the middle of the CPU.

There are different brands, and sometimes the manufacturer of the processors will make two different processor types and improve both. There are many how to build computers instructables and guides out there, but they all tell you to get certain parts. Not only does a good gaming motherboard allow for future upgrades, but it also offers low-latency voice communication for an enhanced gaming experience.

You’ll have to pair it with a monitor, keyboard, and mouse . For suggestions on which peripherals to pick up, check out our roundups of the best gaming keyboards, best gaming mouse, best PC gaming headsets, best PC controllers, and best cheap gaming monitors. In other cases you might need to mount your own case fans, or you may even choose to run your computer without any case fans at all. The I/O plate is an input-output plate which is simply a metal cover that is customized to your particular motherboard. You’ll need to remove the default I/O plate that may have been supplied with your case and swap it out for the one that came with your motherboard.

Step 10: Connect Case Fans And Front Panel Connectors

Depending on the case and how drive bays are configured, M.2, 2.5- and 3.5-inch drives may be able to be installed at the same points or using dedicated brackets. We’ll go over how your PC case may have both configured below. With the CPU, the cooler, and RAM modules installed, the motherboard is ready to be screwed to the backplate inside the case.

Even if you’re a complete beginner, there IS an easy way to build your own PC, and we shall show you how to do it right here. You’d be surprised as to how “user friendly” Linux has become since its creation in the early 90’s. Today, its hardware support and ease of install rival, and in some cases, surpass that of Windows. If your motherboard has a built-in video adapter you want to use, skip this section. Before you begin, you should make sure to have a #2 Philips-head screwdriver, Needle-Nosed pliers, an Anti-Static Wrist strap, and a large, level work space.

  • Your motherboard may have HDMI, DisplayPort, or older DVI or VGA ports, driven by the integrated graphics GPU inside some processors.
  • Attach the processor to the motherboard by finding the processor port on the motherboard’s surface.
  • We now have power to our storage drives and the motherboard, as well as data channels between drives and the mainboard.
  • Make sure that they are tight enough that the CPU cannot wiggle around, but don’t overtighten.

Installing a CPU cooler differs depending on the cooler you’re using, so for specific instructions, please refer to the manufacturer’s manual or support site. Here are some simple instructions that apply to almost every cooler. Do this by gently pushing down on the load arm and moving it out sideways from under the hook, and then raising it up all the way. The hook’s lever action opens the plate, which you can easily flip up. The process isn’t designed to be difficult, and as long as you follow the instructions clearly and keep an eye out to ensure the chip is fully seated before you clamp it in place, you’ll be fine. However, there are some subtle differences in the process depending on who made your CPU.

Adding The Hardware

Storage drives are essential devices that hold not only the operating system but also all programs, personal media, and all other data. It’s recommended to use an SSD (be it M.2 or 2.5-inch) drive for the primary OS partition, which enables quick booting and reliable performance. Data can be stored on traditional (3.5-inch) mechanical drives. Bind all the power cables coming out of the PSU together and put them to one side.

Step 5: Install Power Supply Psu

I will make sure to pass along this information about hot to assemble a computer to help him put his new parts together when he gets them. Be careful as there are some items which must be installed in a certain order . Depending on the order of assembly, some parts can get in the way of other parts when trying to mount them, or result in less working space/room inside the case for installing other parts. Whether you choose to build ‘inside the case’ or ‘outside the case’, you can still assemble individual parts in nearly any order you choose. For instance, you could easily switch around steps , or even do what’s called an ‘out of the case’ build. The process we’ve outlined in our computer build infographic is just one of the ways we prefer to build PCs, but there is some flexibility around it.

Plug the largest cabling connector from the power supply cabling into the motherboard power connector. Find the RAM slots on your motherboard; they will look something like the first picture above.. To install the RAM modules, first push on the levers on either side of the DIMM socket, so that they move to the sides. Once the motherboard is installed, it is time to plug the other components. Video Card/Graphics Card/GPU – While the CPU handles most computation, the Graphics Processing Unit handles all computing related to visuals. These plug into a slot on the motherboard and provide a place to connect a monitor to your computer.