“A guide that talks about everything from budget to assembly, with countless useful tips & warnings.” “A general guide that provided enough information to know where to start and avoid most potential problems.” Jack Lloyd is a Technology Writer and Editor for wikiHow. He has over two years of experience writing and editing technology-related articles. Use care when working around the sharp, sheet metal edges of a computer case.
Live streaming has become an indispensable form of new media in the Internet Age, enabling you to share your gaming skills and experiences with friends remotely. Building a streaming PC may sounds professional, but don’t let it intimidate you. Here are some useful advice you should know before you starts. You should pay attention to contrast and especially brightness, which is rated in candala or nits, same thing. Panel type can be In-Plane Switching or IPS, with better color accuracy and wider viewing angles, or Twisted Nematic or TN, known for its ultra-fast refresh rate. Vertical Alignment or VA panels used to sit in-between these two, though newer AMVA panels have improved colors, contrast and refresh rates, and are found in curved and ultrawide gaming displays.
Step 4: Hard Drives
It’s easy to get overwhelmed with all the possible variables in a PC build. Or do you want to reach the highest levels of performance? The common thread with each of these scenarios is the hardware – the motherboard, processor , storage , and memory . M.2 SSDs are another easy step in the process, but don’t forget to reference your manual to find out which M.2 slots you should use first. Your motherboard may have protective thermal guards on your M.2 slots, so remove those first. Once you’ve taken any guards off the motherboard, you can slot in your M.2 SSDs.
When clamped down, the end of the load lever tucks under a hook to keep everything in place. When you unbox your motherboard, the contact array will be covered with a piece of plastic. This plastic will pop out once you open the bracket, so wait to open it until you’re ready to install your processor. Learning how to build a PC is easier than you might think.
You should do this so that the CPU stays as horizontal as you can and makes contact with all pins as close to the same time as possible, however there is obviously some room for error. No force needs to be applied at this stage as this is the job of the retention bracket – the CPU should just fit neatly in its place. Look at clock speed to determine how fast that processor is.
- Zip ties are useful for tidying up all your PC cables and luckily, you most likely won’t have to buy them as they often come included with several different types of computer parts.
- To be able to build your own desktop PC, you need to have the right tools.
- The current models in the 30-series lineup are the RTX 3070, the powerful RTX 3080, and high-end RTX 3090 cards.
- The power supply will usually go near the top or the bottom rear of the case.
- These are incredibly delicate and easy to bend , so be very careful when working around the socket.
- Usually installing the ram is the first step , and then m.2 drives.
During the process, if anything does not seem to fit or make sense, put the parts down and look things over carefully before you proceed. Some operations, especially installing the heat-sink/fan combination, can require pretty firm pressure, so don’t be afraid to push a little harder if you’re sure everything is set up correctly. Route any required PCIe connectors for your graphics card through the motherboard backplate cutout closest to the graphics card. All PCIe power connectors on the graphics card must be filled by a cable in order to successfully power the card. Connect these cables into the graphics card PCIe connectors which will be located at the side or end of the card. This is a processor specifically designed to handle graphics.
Installing The Drivers
Get a quality one now and it should last you two or three computers into the future. Those are two basics, but not the only ones, and you don’t want to rely on them alone. It’s recommended to look at benchmarks for the processors you’re interested in, to get an idea of how they compare.
Do you need a PC for intense gaming or heavy multimedia production? Here are some tips you need to take into consideration when choosing your parts. Check the maximum amount of USB ports on the motherboard before purchasing a PC case. Make sure the case you want to purchase also support enough USB ports as the motherboard does.
The CPU socket is designed to fill these indents, making it easy to line up your CPU and install it properly. Once you’ve figured out how to place your CPU into its socket, do so gently. Do not apply pressure directly on the CPU–simply close the tray and make sure the metal arm is locked into its original position, which may require a bit of force. We’ve attempted to simplify the process of building a gaming PC as much as possible here, but if you’re not familiar with PC hardware, some of the terms in this guide may need some clarification. We’ve briefly explained some of the parts and terminology we’ll be using below. Feel free to reference this section as you work on your build.
Whereas the DDR4 memory in your computer is emptied when there’s no power, SSDs and M.2 drives can store data without power. For SSDs, they use the same SATA connectors as hard drives, but good drives offer read and write speeds of over 500 megs a second, triple the speed of hard drives. These go up to 2 terabyte capacities, some reaching 4 terabytes. If you’re looking for the largest capacity possible and have an extremely tight budget, a hard drive may be an attractive option. For instructions on installing your hard drive, consult its owner’s manual.